Professional Tips and Tricks for Installing a New Shower Unit

Professional Tips and Tricks for Installing a New Shower Unit

Blog Article

Get Quote Now

Almost everyone is bound to have their personal opinion when it comes to How to Build a Shower Enclosure for Your DIY Bathroom.

A successful shower installation calls for mindful planning and also a great deal of job. Most of the times, you will certainly need to do three kinds of tasks: mounting walls, installing the plumbing, and also finishing walls.

Prep work

First of all, you must decide on the type of shower that you desire to install. It is essential to determine whether the chosen shower can handling specific systems as well as can control a risk-free degree of water via the boiler. Many shower units nowadays are designed to be adaptable to various water pressures (such as stored hot water as well as cool mains).
It is additionally important to think about the water stress as well as the preparation of the piping and drain for the shower

Different Sorts Of Shower Units

Push-on Mixer: The hose pipe and also spray parts of the push-on mixer shower device can be linked to the bath tap based on your requirement, and also the water temperature can be readjusted via the faucets. Push-on mixers are cheap as well as incredibly simple to set up. Nevertheless, although the tube connection is easy, it is quickly removed. In addition, it is bothersome to readjust the temperature.

Bath/Shower Mixer: The hose as well as spray of this kind of shower are incorporated with a bath mixer tap, as well as the temperature level can be readjusted via the bath taps. It is a really economical choice and also no extra plumbing is included. Nevertheless, the bath/shower mixers additionally deal with inconvenient temperature level control options.

Manual Mixer: The hose and spray of a hands-on mixer shower system belong of the wall unit as well as the hot and cold water supplies are connected to a single valve The temperature and stress of the water are regulated with either one or a selection of handles (in more pricey showers). Although temperature control is a lot easier in hands-on mixer kinds, they are much more pricey than the previously discussed mixers. They additionally require extra plumbing of hot and cold water system pipes.

Thermostatic Mixer: The pipe and also spray of this shower kind are a part of the wall device and also the cold and hot water products are attached to a single valve here as well. It is full with a built-in stabiliser to self-adjust the water temperature level and to avoid it from coming to be also warm. One of the largest benefits of a thermostatic mixer shower kind consists of hassle-free temperature control. Nonetheless, it is the most pricey of the different mixer options.

Power Shower: A power shower is a single device consisting of an effective electrical pump that is capable of changing both the water pressure and also temperature level. This type of shower can be fitted if there is supply of water from a cold water tank and also a warm water cylinder. A power shower makes the adjustment of both stress and temperature level simple. On the other hand, it is unsuitable for water warmed directly by the shower or where the water is provided by a combination central heating boiler under keys pressure.

Electric Shower: An electrical shower is plumbed into a mains cold water supply and also it heats the water electrically. It is very important to note that for this shower kind to be set up, the keys pressure requires to be a minimum of 0.7 kg/sq cm (10lb/sq in). The unit permits the temperature and also pressure to be changed via a handle. Models with temperature stabilisers are better as they continue to be unaffected by various other faucets elsewhere being used within the house. A major downside of electrical showers is that the control knob just allows for the alternative of high temperatures at much less stress, or lower temperatures at a higher stress. This is troublesome in the winter when the spray is commonly weak and also the keys water is colder. However, this issue is dealt with in some models which are available with a winter/summer setup.

Method

Depending on the sort of shower you want to set up, the shower head must either be suited order to prevent its contact with the water in the bath listed below or the base tray, or it should have a check valve.
Prior to starting, it is advisable to note the positions of the shower head and also control, and to intend the pipe-work included. In addition, the drainage system to eliminate the drainage will require to be planned. Both settings of the wire route as well as the shower button will certainly also need to be thought about if an instant or electric shower device is being mounted.
Utilize the instruction guide given with the shower unit to fit the shower control.Before suitable the pipelines that will supply the water to the shower system, it is essential to remove the water system. In order to safeguard the pipelines, they ought to be given a water-proof covering and also fitted with separating shutoffs. The pipelines can then be hidden right into the wall surface and also smudged over to neaten the general appearance.
Fit the base tray, shower head, as well as fittings.
Link the major shower control to the pipelines that will certainly be providing the water (This might require a women screw thread adapter).
Reconnect the water as well as examination the pipelines for any kind of leaks, as some might need firm.
If you are setting up an electrical shower, bear in mind to switch off the electrical power supply prior to making any electrical connections. Once these links have been made (there should be advice within the instruction manual), the power supply can be switched back on.

Changing Water Pressure to Suit Your Shower

The cold water reservoir can be lifted to a better elevation (sometimes just 150mm (6inches)) by fitting a solid wood assistance below it - potentially composed of struts as well as blockboards. If you select this option, the major and circulation pipelines will also have to be increased to meet the new height of the reservoir.
Conversely, a booster pump (a solitary pump or a dual/twin pump) can be fitted. Whichever kind is chosen, it needs to be attached right into the power supply in order to run.

Piping as well as Drainage

It is best to make use of 15mm diameter supply pipelines, and also make the runs to the shower as brief and also straight as feasible so regarding maintain maximum stress and minimise heat loss. Additionally, by reducing the use of arm joints for pipeline corners, you can decrease the resistance in the circulation of the water. You can accomplish this by flexing the pipelines instead.

A Lot Of Typical Blunders

Violating or neglecting regional code restrictions.

Making use of pipes that are as well small.

Connecting copper to galvanized without making use of a brass or dielectric suitable in between the two.

Not using tape or pipe substance at threaded joints.

Not leveling your components when mounting them.

Not installing an air gap loading for fixtures.

Reducing supply stub outs as well short to mount the shutoff valves onto after the ended up wall surface remains in location.

Not correctly lining up tubes right into fittings or stop shutoffs. (Forcing the nut onto the compression ring at an angle when the tubes is at an angle will certainly cause a leakage.).

When transforming the water back on in your home, constantly run the outdoors hose pipe shutoff or flush your toilets to bleed dirt and also air from the lines. This debris can cause issues in your sink faucets and also other plumbing trim.

How Do You Install a Shower? Follow This Guide

Installing a Shower at a Glance

Tools & Materials: Level, electric drill, caulk, hole saw, cedar shims, shower unit

Step 1: Drill pilot holes

Step 2: Prep fixture holes

Step 3: Move unit into place

Step 4: Caulk corners and base

Step 5: Attach door

Step 6: Install shower pan

Whenever plumbing is involved in a DIY project, people worry about what might go wrong. The truth is that installing a shower isn’t that complicated, and you can save a lot of money by doing it yourself. You shouldn’t need to make any alterations to your plumbing to complete the job, and most of the tools you need will be provided in your new shower kit.

Can I Install a Shower Myself?

Even if you’ve never installed a shower before, you’ll find this to be a project that is perfectly suited for DIYers with a moderate level of experience. Whether you're doing a bathtub conversion or installing a new stall, most of what you need comes in shower kits that you can purchase from a hardware store. The first thing you need to do is determine what type of shower stall you want.

Single-panel stalls are the easiest to install because they come preassembled. All you need to do is put them in place. Multi-panel showers require a few additional steps, but you’ve got more control over the appearance of your unit. Multi-panel units are also much easier to handle if you’re going to do the installation without any help.

Be sure to take all appropriate safety precautions, such as wearing eye protection and gloves. When you’re removing or installing a shower unit, you might kick up debris that could hurt your eyes. You’ll also need to work with equipment that will get extremely hot, so be sure to have safety gloves handy.

Tools and Materials

2- to 4-foot level

Electric drill with a 1/8-inch drill bit

Caulk

2-inch hole saw

Cedar shims

The unit itself

Before You Begin: Prep the Space

It’s highly important to measure your space accurately before putting the stall in. Measuring from the floor upward and from each corner outward will ensure you’ve got the right measurements. What you’re looking for is where the plumbing apparatuses are going to come through the stall. Transfer these measurements over to the back of your unit by drawing the locations of these holes using a pencil or marker.

Pull out your old shower and make sure to scrape off all the old caulking. Be thorough because you want to work with smooth surfaces for the best installation. Once you’ve pulled out your existing shower, you need to make sure that the floor is clean and dry. The best way to clean debris is with a shop vacuum, as it’ll soak up water and dirt together.

If you’re experiencing any plumbing issues, such as low water pressure, this is a perfect opportunity to solve them. Make sure that the pipes themselves are not in need of patching and clean your showerhead. When you turn the water back on after your project, check the pipes for signs of wear or disrepair. Anything beyond minor repairs should be handled by a plumber, and this is the best time to bring in a professional.

If the floor has any moisture at all, don’t proceed until it’s completely dry. The last thing you need is for the floor to rot or invite mold and mildew into your base. Once everything is dry, apply waterproof wallboard to the walls. This can be attached with screws or nails, then sealed with caulk so that water doesn’t seep into any crevices.

https://www.homeserve.com/en-us/blog/how-to/install-shower/

Hopefully you enjoyed our part on How to Install a Shower Enclosure . Thanks so much for taking a few minutes to read through our article. In case you appreciated our post please make sure you remember to share it. I enjoy reading our article about How to Install a Freestand.

Website

Report this page